MB1 Mini Boom Stand

This thing is heavy which is great. Running it with a Sennheiser Mic in front of a guitar amp and its a great stand. Very adjustable and it definitely wont move on its own.

I use this stand for micing my acoustic drums. It can be great for micing the front or even inside of the bass drum if you have a port hole. However I only have a two mic setup currently, so I mic the side of the bass drum diagonally, to get some click from the beater and pick up some of the other drums and cymbals as well. This stand works great because of the weighted base and for any of your low height micing needs. I think I briefly used this as one of my stands to mic my Boss Katana 2x12 combo amp. It makes micing an amp a bit easier too and reduces the profile of the equipment around the amp and working area. Though this may be a bit expensive for low height amp micing. You could probably get an average low height mic stand unless for some reason you really need to reach with the stand to get the mic where it needs to go. Still a good stand and not so expensive for a name brand.

I've used a Samson MB1 Mini Boom Stand as a desk stand for five or six years. It offers great flexibility with adjustable height and with a two-piece (telescoping) boom that allows great reach and balance. There's a small counterweight on the end of the boom (opposite from where the microphone attaches) that helps counterbalance the boom. Here's where gravity comes in: The heavy-duty base isn't round; it has three fixed-position legs or "feet." If you position the microphone so the boom extends over any one of the legs, the stand is not likely to tip over. But if you position the microphone between the legs, of course it's going to tip. I use the microphone and stand on my desk. The stand is positioned to the left of my computer monitor, and the base is rotated so that one of the three legs points directly at me. That means another leg is at right angles to me, pointing to the left. When I want to use the mic, I rotate the boom (I keep the boom loose on the vertical post) so the mic is positioned over the leg that's pointing at my mouth. When I'm through with my recording work, I simply swing the microphone to the left, over the leg that's pointing to the left, and the mic is out of the way and solidly supported. There are four adjusting clamps (one to control the length of the boom, one to control the horizontal placement of the boom on the vertical post, one to control the angle of the boom, and one to control the height of the vertical post), and they all work well. I've returned to this Amazon page to buy my second Samson MB1 Mini Boom Stand, to take on the road. In the past, I've used the stand on my desk when going on the road, but I'd prefer to have a separate stand with my portable equipment so that I don't have to "rob" my home studio every time I need to go on the road. I've looked at close to a dozen stands. This is the only one I've found with three legs or "feet" that comprise the base, which results in solid support without excessive weight.

First things first, I have absolutely zero experience with this type of gear. My background is photography (cameras, lenses, meters, radio control devices, tripods, studio flash gear, et cetera), construction and pest control. My experience is what tells me this is a well made piece of gear that I wouldn't hesitate to take to a construction site or a photo shoot. I'll be using the stand to hold an omnimic to do room analyzing measurements with. http://www.amazon.com/Dayton-Audio-Electret-Measurement-Microphone/dp/B002KI8X40/ref=sr_1_sc_1?ie=UTF8&qid=1354286429&sr=8-1-spell&keywords=Daton+EMM-6 If you need to add more weight then the stand is designed to hold, then add more counter weight or get a heavier table stand. There's no excuse for overloading one's gear. I worked thirty years in the construction trades and I'm use to putting gear through it's paces to tear broken things out that are made of big timbers, pipe and steel, and put them back together again with power saws/drills and big heavy hammers; Milwaukee, Skill, Ridgid and Stanley tools. The point, I know how to use gear to it's max and after many years of use, not break them. The point, if anybody tells you this is a fragile piece of gear, it's because they're abusing the gear beyond what it was designed to do; at a reasonable price, hold a microphone in a static position and then be moved again. When using this stand, if the mic is falling over, it's because it's being over extended, over weighted, poorly cabled, not leveled or the legs of the stand are improperly positions; one leg should face away from the weight load in the direction of the tilt. The mic stand is not falling over because it's not stable, the base is too light or it's poorly designed. If parts are breaking it's because the parts are being overtightened beyond what they were designed for. A little bit of common sense regarding not abusing your tools goes a long way in extending their usefulness. People who break their tools and then blame the tools, tick me off. And yes, we all have experienced products that broke the moment we plugged them in for normal use. That's what a warranty is for. I don't care what the other reviewers have to say about this mic stand. It's a beautiful piece of gear, that's well designed and will give it's owner many years of service. Eventually, one day, years down the road, the parts will get old, brittle and break but don't we all. Based on personal experience with lots of tools, used under extreme conditions (heat, cold, dark, rain and under houses), I expect this piece of gear to last many years of regular use and then if it breaks, without complaint I'll say; I got many years of use out of it as I only paid $27.00 for the stand and that included delivery. The point, for a well constructed mic stand, this is a great price. You'll be hard pressed to find a better product at any price and yes, I've looked. I do have one niggle and that's the hand-twist action at the center of the stand to tighten the center clamp of the main support. It's a bit flaky as to tightening but with patience, it locks things down just fine. This niggle is not a reason to take this item off a list of possible choices or an excuse to knock a star off a possible five star rating. If one is expecting a table top mic stand they can throw around the stage in anger to impress everybody (Oooo, he's scary) with their lack of personal self-control, get an all metal stand who's clamps are made of steel or get a different profession where, due to their lack of self-control, won't be able to break things. If one is going show self-control and respect their gear, expectedly, this mic stand will last many years and like most well used items, eventually die a gentle, quiet, well deserved death. I love this stand because it's well made, is good looking, has lots of well placed adjustments to make it very functional and delivered, is well priced. Hope the above review helps.

Stable, sturdy, no issues with mic weight and boom arm. Small footprint. Build quality justifies the price. Swapped out the mic holder to fit my sm57s more comfortably but I will be buying another.

Heavy narrow base and long reach make this an excellent stand for a snare drum. Clamp a small goose neck on the shaft and you can add an under-snare mic also. Much cheaper than LP Claw options. (See picture)

Good product

Incredibly solid for the price. The bottom base is a heavy die cast piece that will last for centuries. The box it came in is way to big for the dimensions of the product, in my opinion, the manufacturer could cut down shipping costs with a smaller box. Anyway, excellent quality. Thick metal were is most important, and good quality plastic for the rest. I don't usually write reviews, but Samson made a great job with this product.

I was looking for a stand I could use on my desktop to support a Rode or Samson studio mic for video editing. Most stands have a small base and so tend to topple over. This one does the job perfect. The triangular (rather than round) base makes it easier to position, but the base is heavy enough to handle my mics without the boom toppling over. Its good quality, boom itself is telescoping so easy to adjust. Absolutely perfect for what I needed.

This is an awesome desktop Mic Stand. High quality construction, including connections. and heavy cast base makes for a mic that will not move when mounted. Highly recommended.