Arizona Rim Country Arizona Carbon E-Z Fletch Pro Tool

Works great. Not too expensive. Easy to use. Used it for my Easton Sonic 6.0 and the fit and this made it simple with the larger diameter arrow.

this fletches perfectly just like a professional. my arrows look better than they did when I got them fletched from a bow shop im never going to have some bow shop take 3 weeks to fletch my arrows ever again. it takes about 65 minutes to fletch 6 arrows. this fletching jig works great. just make sure you get the nock lined up in the slot its supposed to go into if you don't pay attention you could get it set up off set and your arrow wont fletch correctly. and the pins are a little hard to get out when changing arms. it works great with 5 inch feathers and you can use 4 inch vanes or even 2 inch vanes. if you want to do feathers and 2 inch vanes I recommend getting this and the mini arms for the 2 inch just because the mini arms have a gnarly helical. but this does good 2 inch vanes as it is now.

New to fletching, and, while I'm probably not saving all that much on a dozen or so arrows twice a year, I enjoy this sort of stuff, so I made the modest investment. Steep learning curve, for this dolt, because I missed the bit of instructions that tell you how to align the arrow nock bar in the base with the slots (in fairness to the reviewer, this pearl of wisdom is on the right hand side of the page and not included in the main text - maybe it was added later?). In any event, after screwing up a few vanes, I made some serviceable arrows. Then I discovered how to align the slots and things improved considerably - new fletching is easy, and I can now replace/repair just one three vanes with no difficulty. Because I'm new at this, and exactly as they warn against, I used too much glue in my first attempts and ended up with some rather unsightly shafts. They shoot just fine, and I'm not embarrassed to look like an amateur when, in fact, I am an amateur, but I'll probably get around to cleaning them up anyway. All in all, this jig works very well and is easily mastered - for you, perhaps fifteen minutes and one or two attempts; for me, longer, but not all night, either. And if you screw up, that's what that scraper tool is for. Do it again. Not a big deal. Works for me, and I recommend it strongly.

The box arrived in terrible condition. Look's like it was absolutely put through the wringer on the way to me. The actual fletcher works just fine. It feels incredibly cheap (flimsy and brittle), but I have watched my local pro shop use them over and over again so they clearly hold up. Definitely need to read the instructions. It seems simple to use but you could break it pretty easily if you pull on it wrong. For the price, it is a good buy. ***updating after some more use. The jig works fine for vanes like blazer 2”, but it is not able to consistently attach AAE trad vanes. They appear to have a thinner piece that attaches to the arrow and so the vane slides into the groove too deep and gets glue on the jig. I will have to get a new jig for the trad vanes as it constantly is getting stuck to the arrow and pulling the vane off when I open it.

I just finished fletching adozen arrows with this. I am absolutely satisfied with the way it works, and it's dead simple. I also have the "carbon straight" version, and would offer the same comments about it. This is a great tool and I strongly recommend it for both repairs and new arrow construction. If you're using superglue type fletching products (cyano-acrylate) be sure to use a gel, not a liquid. Liquid superglue will run down the vanes and get super sloppy around the nock end of the shaft. Gel type superglues stay in place on the vanes and produce little mess. The material the tool is made of is relatively easy to clean dried superglue off of, it just dries and crusts up and you can pick it off with a utility knife or a dental pick.

Recieved out of factory package and missing parts

I received this fletching kit several months ago, and did not get a chance to use it for awhile after receiving it. I have now used it to fletch a couple dozen arrows, and I can say that, for the money, it is hard for me to imagine that it can be beat. Very, very simple to use, and everything lines up perfectly. Arrows I've fletched with this tool fly every bit as true as those with factory fletching. I've used it to refletch arrows on which the factory fletching has been stripped or ruined, as well as to fletch some that came without factory fletching. I have zero complaints. Cheap, and maybe cheap-looking, but amazingly accurate, handy, and efficient. I recommend this tool without reservations.

This thing is a giant waste of money. It just bends feathers and glues all the spines ruining the feather. You have to check the alignment constantly too because if you actually get a feather attached to the shaft of an arrow only probably half of it made it so it screws your alignment up then. Its also made out of cheap, flimsy plastic. For 50 Dollars this should actually work, but it doesn't. Save yourself the hassle I bought a right and left wing one, for that amount of money you could get one made out of metal that can fletch one feather on five shafts. You practically have to only do one feather at a time anyway because the locking mechanism is so cheap it doesn't close the plastic. The manufacturer should be ashamed they even make this, much less sell it for 50 bucks, 10 or 15 maybe. It probably does okay for Vanes but Im not interested in that. It's still a piece of crap.