VHT ESP100000 FlameProof Coating Flat Grey Primer Can - , 11 Ounce (Pack of 1) (SP100), Packaging may vary

I used this product in conjunction with an appropriate primer and clearcoat, all from VHT, to paint my car's brake calipers bright glossy red. I'd suggest a white primer for any bright color. Grey primer works well too, and gives a deeper finish. Black primer should really only be used for a black base color. step 1) Wearing a respirator (if possible), remove brake dust, grease, and rust using a brake caliper cleaning agent of some kind. Also use a wire brush if you can. step 2) Sand your calipers using 320-grit sandpaper. Really rough them up. Then use some more brake cleaner to remove whatever you sanded off. step 3) Mask off your car's corner body panels, the wheel wells, the struts and hoses, and finally, the brake rotors. Take the time to mask the bleed valves on the calipers too. step 4) Apply primer (THIS PRODUCT!!) to the caliper in a very light, speckled coat, then move to the next caliper until you've applied a coat to all 4. Do this 4 times, gradually getting heavier, but avoid letting the paint run (it's okay if it happens in the primer). Try to do this as quickly as possible. step 5) Apply your base color using the same method as in step 4: light coats multiple times. I suggest a sweeping method, rather than just spraying hard. Do NOT allow the base color to run. step 6) Apply a clear coat using the same method as in steps 4 and 5, but be careful not to overdo it. Clear coats can run more easily than base colors. The paint should be looking thick and glossy by this time. step 7) Wait about an hour. Drink a margarita, or call your mom. step 8) Remove your masking. Gaze upon your new calipers. Then, use some brake cleaner to remove any overspray from the brake rotors or undercarriage areas. Do NOT use brake cleaner to clean body panels, as it will probably remove the paint. step 9) put your wheels back on. wait a few more hours. THEN drive your car pretty hard, making sure to go fast, and brake hard. This will heat your brakes up. The paint needs to cure at 200ºF, which means you need to drive and brake repeatedly. Don't go too nuts. Your paint job is complete.

My favorite header paint for race car application. it doesn't burn off. Easy to touch up. Drys fast.

It is not the first time I am buying and using this High Temp Paint spray, either Flat Black or Glossy Black. It is relatively expensive and it provides good results on hot surfaces: it depends very much of the kind of the surface and the preparation work being done before the application. In my opinion, it provides longer durability when applied over a cast iron part (ex: exhaust manifold) than o a new exhaust pipe or muffler -- it will start to flake after several months, in particular off the aluminized or factory painted (exhaust) parts. On older exhaust parts, I had better luck after removing the surface rust and cleaning with good brake cleaner. Painted over the exhaust wrap... mixed results. It the wrap is in areas that are some more exposed to whatever flies under the vehicle, the paint and (later) the wrap is not going to last long, as they are not quite abrasion resistant. Otherwise: read and follow the instruction.

Header paint that doesn't burn off if you do it right. Did it on my 4x4 now on my Camaro. Holds up fine. Kinda reminds you of soot so let it cure good. Don't wear your best shirt when installing. Doubt there's much heat dampening but I'd rather not wrap nor donate a kidney to be able to afford jet hot

Got the paint, rattle the ratsh-t out of it for over the span of 2 days without a mixing ball. Said to heck with it since I'd like to wrap up my project and only need the paint and primer to function as a sealant of sorts. I used Rustoleum 2000F Primer and cured once at 250F, once at 400F and twice at 450F (my oven doesnt go up to the recommended 600F) The primers finish came out great, I received this can of VHT and after deciding to just "send it" despite the lack of mixing ball, off I went. I made sure to shake up the paint as good as I possibly can to give it (and myself) the best shot. I was expecting dribbly nozzle action. The can worked as normal, the spray pattern and atomization seemed unaffected (keep in mind I shook the hell out of it for at least 3 collective hours). I cured this the exact same as I cured the primer. The finish was pretty good except for a few spots where I may have oversprayed a little bit, only very slight miniscule bubbles on one or two areas. I let it cure again at 450F which seemed to harden up those bubbles a little more so I figured it was fairly well cured. Lots of off-gassing smoking when curing, do not do this indoors. I expect more smoke when the car is started. Other than missing a mixing ball, which the rustoleum primer definitely had, I guess the product speaks for itself. This part is completely hidden in the engine bay, this was just to help the 40 year old iron with heat dissipation and to possibly prevent a surface crack from spreading. The paint was used for it's utility and not aesthetics so I suppose it's not a bad deal. Shipping was awful, but again a fault on my part since I didn't bother to check local stores. Almost a week coast to coast.

I am satisfied with the quality, delivery time and packaging.

Sprays easy, looks great.

Perfect

乾燥も早く綺麗に塗装できました。 スプレーのプッシュ感も良かったです。 まだ、塗装したばかりなので耐久性はわかりませんが、良いことを期待します。

EKシビックのマフラーに使用しました。 何カ月かたったが剥がれなしです！

The paint itself is fine, did the job as expected. The can nozzle though on mine got stuck the second I tried to use it and it would not stop spraying. I ended up having to do multiple coats in a row cus I had to hold a rag up against the nozzle to stop it. Paint job came out ok in the end but I ended up having to waste what was left of the can and let it just spill out into a bucket. How do you screw up a nozzle?

購入1本目は塗料が噴射されず返品、ダメもとで同じ販売店から2本目を購入。 2本目は問題無く使用出来ました。