Peel and Stick Metal Molding Trim, Self-Adhesive Stainless Steel for Wall, Fireplace, Mirror Edging and Craft Decoration (Brushed Silver, 20ft x 1in)

I ordered one that was used. It was already cut in sections which worked for. The edges are sharp and I cut myself so be careful. Stick rating is very good. If you mess up, you will take paint off like I did. The metal was a plastic covering on front which protects it until you use it. It shines! I am impressed. If you need a stainless strip that self sticks, this product is for you.

This fit my fireplace trim perfectly and changed the brass to brushed nickle!

This metal trim is very easy to apply and it stays put. Looks very nice around our bathroom mirrors and almost matches the brushed nickel hardware, faucets, etc. You can't tell the difference unless you really look - it's a bit shinier. Love it except the edges are rather sharp, even after the product has been applied. You need to be careful when cleaning around it as you can still cut yourself. I was cleaning my mirror with a paper towel and got a long gash on the side of my hand.

After reading reviews of "Amazon Vine" members, I see that Amazon has a wide window of acceptance for this Appellation. The photos of this trim on Amazon explicitly state " Please wear gloves and cut with tin snips". Nonetheless, several "Vine" reviewers complained that it was hard to cut (using household scissors? - no kidding?!) One Vine person even thought this SS trim was aluminum! Another thought a magnet could stick to it (perhaps that person was sent 400-series SS, rather than the 300-series that I bought?) But here is my biggest shock - not a single reviewer measured how thick it was nor explained the sharp edge problem. My review of the 1"-wide SS strip: The cutting process that the factory uses apparently creates a razor-sharp burr that points away from the finished surface. Please see photo#1. I was able to use a carbide-tipped tool to remove this sharp edge manually from 3"-long strips that I cut, but it took some effort, for sure. As of my writing, not a single reviewer has mentioned how thick this SS trim is, even though that was certainly of keen interest to me. I used my micrometer, after de-burring, and I measured a thickness of 0.011"-thick. (To be diligent, I spent some considerable effort to scrape away all of the burr) I purchased this trim to act as a force-spreader for a "girdle" that I built to reinforce weak spots on 65-gallon HDPE rain barrels that I had purchased. After fusing the cracks shut and fusing SS reinforcing screen into the barrel wall over the cracks with an extra coating of melted HDPE, I wrapped four 1/32" multistranded 316SS cables around the circumference at a height where the HDPE wall had split and leaked. The barrels are actually rounded octagons, and this means that there are eight high points around the circumference where the tension cables might cut right into (and through!) the HDPE barrel wall, so I cut 3" lengths of Coengwui SS trim to go over the high points. See photo#2. I transferred 65 gallons of water into the barrel and, so far, no leaking and no taut 1/32" SS cables cutting into the barrel, notwithstanding 520 pounds of water inside. The 0.012"-thick SS trim is unimpressed by the taut cables.

It looked good for about 2 hours - then it began to lose its stickiness in various places. I used it on three different mirrors and they all had problems with staying glued down.

I used this product to cover up the gold edge molding between the mirror and the counter backsplash. Everything in my bathroom was brushed nickel except this piece. I never knew how to cover up the gold mirror trim until I came across this product. The application was easy. I would suggest using a sturdy and sharp pair of shears to cut the metal molding so that you get a clean, nice looking edge to work with. Do wear gloves because the edges of the molding are a bit sharp and can cause a paper cut-like cut if you are working with bare hands and happen to run your finger over the edge while smoothing out the metal trim. Once you have installed the trim and smoothed out the bumps, etc., go back and apply pressure, in smaller sections, along the length of the trim to ensure a good adhesion.

So disappointed with this stripping. It is so stiff that it bounces back at you while you are trying to cut or place it. Worse than that, the edges are extremely sharp after you cut them. (Need to file them down for safety's sake). Definitely NOT a product for kids' projects! I was able to use it to replace damaged trim on my appliance, but it was a bear to work with.

Worked great for trimming around SS range hood

viene muy bien presentado y con las indicaciones básicas de uso

Sobald man die Schutzfolie abzieht, ist die Farbe etwas heller und glänzender als auf dem Bildschirm zu erkennen ist. Qualität ist aber einwandfrei. Die Klebefläche ist nur mittig vom Band und geht nicht ganz bis zu den Rändern, hält aber super gut auf funierten Untergrund.

Parfait !!!

Le ruban se bosse trop facilement en l'appliquant.