Braava 380t Compatible Tires/Tread/wheels/rubber/320/321/375t/390t/Mint Plus 5200/4200/available Tyres/iRobot(1pack=2pcs) tire/tyre/treads/Wheel/Rubbers

Holy cow, better than new... Works wet no problem for me! 2 minute install, running faster than new. Looks cooler too. I was worried that they'd be a little loud with the tread, but no noise either. Full story: I was having the issue were the Braava 380 was just spinning and doing a weird dance, then beeping 6 times. I had bought 2 batteries awhile back, so popped in a new one of those after some reviews suggested it was just getting weak. But same issue. So I laid on the floor and watched her work... It was really that the tires were coming off and getting stuck in the sides or just looping over themselves (disappeared when I lifted her off the ground). Watched the suggested youtube video and replaced with these in two minutes or less without disassembling at all. Still even have the original worn out tires in tact. You just slightly offset the tire to the outside and spin... Then do the reverse to reinstall. Easy if you've ever fixed a kids toy like an RC car. Super happy with this purchase. Great price, quality product.

Super easy to put on the tires without taking the robot apart (although you do need to pull off the old foam ones, which are glued on. Just cut across a section and pull slowly and you will get it off). I did have a problem with these tires slipping while mopping the kitchen but after experimenting I discovered 2 things I did with the old tires that won't work with these tires. 1. I usually spray the kitchen tile with water from the faucet and let the robot mop through it. The robot is definitely not as tolerant about that with these tires and so I found that "just a little" pretreating of the bad spots (rather than the whole floor) seems to work fine. 2. When placing the cloth in the mop holder I like the cloth tight against the bottom so there is cloth extra cloth in the center channel that connects the holder to the main unit. The cloth in the channel keeps the mop holder from fully locking in, and therefore it sits a little lower to the floor than it does if the center channel is clear (a good way to tell is that if you pick the robot up and the mop holder stays on the floor then you likely have cloth in the channel). This in turn puts more force on the wheels causing them to spin. After I made the cloth looser on the bottom so there is no extra in the channel the holder snaps in like it should. The robot seems to work fine like this. I will experiment further and update this review if I learn anything new. UPDATE: I took some fine grit sandpaper and scuffed up the wheels a bit for better traction. The robot is pretty much working as it did originally :)

These little tires had my Braava 380t Robot (formerly Mint) smoothly gliding across my kitchen linoleum floor just like new! No slipping or sliding -- excellent traction without sanding. Pretty easy to install, even with my small hands. I removed the remaining foam and used the end of a chopstick to help. No need to remove wheels. Just remember to put a towel down before, though, so as not to scratch the finish. Prior to installing, robot was sluggish, beeping six times, making slow turns -- could tell it was because of wheel imbalance due to tread wear. Thank you for making these -- made my robot happy and and kept it out of landfill!

This porduct is amazing! The tread on 1 of the tires of my Braava 380t was lost. I called up iRobot and they said I need to buy another new Braava robot since they can't help me with the tread. This was really odd. The robot was working just fine and I needed a replacement tread, definitely NOT a new Braava. After going through the reviews of this particular tread model, I ordered it. It came in about a week, installation on Braava was easy (looked up a YouTube video) and the iRobot Braava has been working perfectly!! Can't be more happy. It actually makes the Braava go a bit faster than before and so the room is mopped in less time, so I can again use the Braava in another room without recharging it. The mopping is done well even if it goes a bit faster than before. Thank you for making such an amazing product. It saved me money and I did not need to buy a new Braava.

Changed original tread as the rubber was getting slipping. This is more expensive than the wheel plus tread being sold on AMAZON but bought this instead as this had better reviews that than wheel plus tread. Besides the wheel installation looked more tricky. ROVAholic has posted a method to slip on the new treads without opening anything on the 380t which worked well for me. So ease of replacement 5 stars for sure. Worked perfectly (on day 1 at least!). As another reviewer said the 380t is more brisk now - appeared a bit hesitant with the worn out tread. Rovaholic installation U tube does not show removal of old tread. So here goes - Make a slit on old tread with a knife or rip it with finger nails. If you remove it carefully you can strip it off in a few pieces - it is glued to the wheel. Be sure to clean the wheel completely to remove glue residue and old tread bits, it will ensure a good fit for the new tread. Note the new tread is not glued on and is of a stiffer material than the old one. Cheers!