Mag Drill Press, 1550W 2" Boring Diameter, 2922lbf Power Magnetic Drill, 500 PRM, 10-Speed, Electric Drilling Machine for Metal Surface, Industrial and Home Improvement

Bought this when I started a house renovation project in a metal building to drill through the beams. Have used both the standard drill bits as well as the Walden Shank bits. Both work great! Never used the Walden Shanja before this but boy do their hole saw bits but well! I installed a mini split system and had to run the line sets through the beams and used this drill with a 2" hole bit to run them and it couldn't have worked better! Was able to drill each hole in like 30 seconds! Incredible! Also the drill is extremely durable and solid. Accidentally fell off my work bench once onto a concrete floor and was perfectly fine. Great drill! If you need a good mag drill that isn't over a grand this one will suit your needs!

For me, this mag drill from Vevor has been great. Upon receiving it, I needed to adjust the gibs for the vertical travel. It's an easy process of gradually snugging up the adjusting screws until you get the desired amount of resistance. Then, tighten the nuts to lock the screws in place. When I received it, the screws had the travel locked in place. I assume that was for shipping purposes. I am now about halfway through the job for which I bought this tool. So far, so good. I am running a 5/8" annular cutter to modify a laser table. I machined a simple fixture to locate the cutter, and the magnet is then energized while the tool is centered. There is virtually no movement when powering the magnet. The base is square to the travel of the travel. There hasn't been any noticeable runout in the spindle. I am more than happy with the accuracy and function of this machine. For what I paid (well under $200 USD), this tool has gone well beyond my expectations. I don't know how well it would hold up to heavy duty use, but it is working beautifully for my project. Thus far, I've found that the tool has no trouble pushing the 5/8" cutter through the 1/4" steel plate. It says it will handle a 2" cutter, but I don't plan to ever put it to that test. If I put some pressure into the 5/8" cutter, the motor will start to labor. However, for this type of cutting, you've just gotta keep things lubed and let the cutter do the work. I don't know how often I'll need this tool in the future, but I feel it will have paid for itself if it makes it through this job. It is a fantastic value.

I had a particular job I purchased this for. I needed twelve 1/2" holes drilled in a plate of steel that's 2 1/2" thick and stands up at a 90 degree angle. I knew a mag drill was the only practical way to do it so I figured I'd try this one since it was affordable. It worked perfectly. No problem at all with the magnet holding the drill up there while I spent a couple of hours doing the drilling. The adjustable speed worked great with the different sized bits I was using. If I had to complain about something it would be the magnet switch and drill switch being located so close. Several times I wasn't thinking or paying attention and turned the magnet off on accident. Nothing like watching the drill take off falling when you're not expecting it. It may not help me but it would be nice if the switches were at different locations. Overall I'd say if you're on the fence buy it.

With the chuck attached, it takes short drill bits. It could use ann interlock to prevent the drill from starting without the magnet energized. Otherwise good machine for the money.

I wish that I had bought one of these a long time ago. Annular cutters work so much better for putting holes in steel plate than ordinary drill bits. The magnetic base is very strong and holds the machine solidly in place. The variable speed is awesome and in my opinion this a "must have" feature to extend the life of the cutters. Don't forget to use proper lubrication on the cutter as well. I didn't install the included oil dispenser system and instead just put a dab of Hougen 11748 RotaGel Cutting Lube on the cutter before drilling each hole. Time will tell how well this holds up to heavy use, but at this point I'm very pleased and would definitely buy it again.

Works great, very good price, quality is good

Check the switch cause no problem with the magnet but the drill doesn’t start at each time sometimes I have to play with the switch to strat the drill

I can't get a straight drill on this thing, and can't replace the bad drive shaft with something straighter. Definitely would be a great drill if it were a straight drill though. Plenty power. I had to buy a second drill press for when tolerances matter.

Machine works effortlessly drilling 14mm holen through 1cm thick steel like butter. Drilled almost 200 holes over the weekend and can't find any flaws. Only remark is that with the drill head installed the head becomes heavy and drops making it slightly more difficult to position the drill. Very happy with the purchase. I can recommend this to anyone having second thoughts.

Super soddisfatto ! Robusto !

It performs flawless The only downside it has no speed control Otherwise fantastic

A priori se le ve buen taladro, parece de construcción muy robusta, su funcionamiento es correcto y ahora queda ver la durabilidad. He de decir que no me traía la cinta de amarre de seguridad y que al pedirlo me confundí y no lo pedí con el deposito de refrigerante de corte y ahora he querido pedirlo con opción junto con su soporte, y no lo encuentro por ningún lado

stabil och bra maskin