B-Tech BT77 Ultragrip Pro Speaker Mount, Set of 2, Side Clamp with Tilt and Swivel, Black

Great product that suited my needs Used it to hang a bookshelf speaker 6ft above on a wall. Easy setup. Sturdy finish. It may even support heavier loads. Locking the speaker is easy and the bolt cover made the finish look professional

After searching the various internet sites, I finally found what I hoped was a speaker wall bracket that was strong, would take a heavy speaker without having to damage/screw holes to my bookshelf speakers, and once fitted to the wall, would allow me to not only angle the speaker to my required line of sound, but also tilt slghtly to point the speaker down towards the listener position. Once arrived I eagerly opened the box and the first thing that I realised was the build quality, with all the parts being very easy to assemble and of top quality. Even the glossy black cover is made of a strong high quality finish plastic. The excellent side clamping method to secure the actual speaker is very positive and holds my 7kg bookshelf speakers tightly without leaving any scuff marks or having to screw the speaker in position. If you are looking for top quality speaker brackets that not only look great, but are functional and very versatile then these are the brackets for you. The box includes a pair of brackets, all fittings and screws, washers etc, and ample wall plugs and screws. All of high quality. Highly recommended. Full 5 stars for this product. Not the cheapest but certainly the best in my opinion.

I bought these to mount some Q Acoustics 2020i speakers on a sloping attic ceiling. These speakers are fairly heavy and so the maximum weight rating for the clamps was important. Rated up to 25 Kg they are well capable of carrying the 5 Kg that the speakers weigh. The clamps are well made , very sturdy and easy to fix up but one oversight in their design is that there is no provision for hiding any rear entry cable . To get round this problem I drilled a hole through the top of the metal box section that sits under the speaker support plate. By placing this hole about an inch from the back of this strut (near to where it joins to the wall fixing plate ) I was able to thread my cable in from the rear and up through the hole I had made. Fortunately the box section is open at the rear to allow this.I also had to make a slight hole in the plastic covering plate to allow it to slide over the speaker wire. Doing all this will enable connection to speaker terminals on the back of any speaker or , as in my case , to speaker terminals placed on the bottom of the speakers. Because I was using speakers with terminals situated underneath the speaker I had to make my connections before actually fitting the speaker to the clamp's speaker support plate. As I was doing the job alone I fitted banana plugs as trying to connect bare wire would have been very awkward whilst up the ladder and carrying the weight of the speaker. I found another problem with my choice of speaker was that they have rounded edges at both top and bottom and this meant that the clamps only had a very small contact area with the sides of the speakers. It was insufficient to support my speakers properly as they face down to the seating. To get round this I made some wooden inserts to fit in the recess underneath the speakers utilising existing screw holes . I then made a couple of small holes in the clamp base so that I could screw through it into the wood. I don't think my speakers will ever come adrift and it was all achieved without any permanent modification to the speakers. There was ample adjustment on the clamps to point the speakers exactly where I want them and I am very happy with how things have worked out.The finished job looks very neat and tidy. I have only given the clamps four stars because I had to modify them to hide the cable and this is something B Tech should have built in to the design. In all other aspects they are a five star product.

These B-Tech BT77 speaker wall mounts were really easy to install using my basic DIY tools and skills. You need to ensure that you use appropriate fixings. The BT77s were very solid on the wall and easy to adjust. I like the way the fixing screws are all hidden by the cover plate. I was confident in mounting my heavy (12kg) speakers which measure 10 x 10 x 22 inches. The brackets and speakers were mounted and adjusted within an hour. To avoid cosmetic damage to visible parts of the speaker I didn't put screws though the side brackets into the speaker. While you can tighten the side brackets sufficiently to prevent the speaker sliding off the mount, I did put a screw through the hole in the base plate into the speaker base to provide extra security and stability: this enables me to tilt the speakers fully forward without any worry that they will slide off and this arrangement appears adequate for this size of speaker. I'd certainly buy these BT77s again if I was looking for a quality, functional speaker wall mount. For the price they are excellent.

Perfect product. Wanted something to mount surround speakers at a ~80 degree angle against the wall. Saw complaints in reviews about build quality, exposed hex nut on the bottom, and needing to drill your own hole for cable routing. IMO build quality is fine: the cover plate is sticking on fine for me. Had to make a tiny notch in the hole in it to get the cables I'd routed through the arm through when I slid it on. However: It comes with a plastic cover for the exposed hex nut at the bottom. Another review complained about it being exposed. I guess it's still not a thing of beauty but it looks fine IMO. There is a hole drilled for cable routing out of the wall behind the back plate which works perfectly (Though it's not huge, might be hard to get anything other than speaker cable for passive speakers through) My speakers aren't huge, but it's pretty sturdy even just screwed into plasterboard. I won't be deliberately swinging on it but I'm not worried about knocks. (And if you put it into something more solid then you could swing off it all you want) TL; DR: Buy this one

These are most definitely heavy duty work fabulous, would highly recommend.

J'ai cherché partout des supports muraux pour mes enceintes triangle Cométe EX (qui font déja leur poids!), aucun produit ne correspondait à ce que je voulais. Je suis tombé par hasard sur ceux ci, et je dois avouer que j'étais septique quant à la qualité au vue du prix, et bien non, au contraire, ces supports sont tout simplement excellents ! Ils inspirent confiance (et il vaut mieux vu le prix des enceintes!), pour un montage sur du ba13 attention, utiliser des chevilles molly, et si comme moi vos enceintes sont assez lourdes, renforcer le placo si possible pour éviter les mauvaises surprises! Concernant le systéme de fixation de l'enceinte, c'est très simple, l'enceinte est serrée sur les cotés (en contact avec un caoutchouc anti-dérapant)dans mon cas j'ai vissé l'arrière des hp pour assurer le montage et ainsi éviter un glissement car je les ai réglé vers l'avant. La seule amélioration que je pourrais formuler serait d'avoir un passage du cable (mais c'est vraiment un détail), j'ai percé la plaque en plastique et le tour est joué, installation digne d'un pro!! Bref si comme moi vous recherchez un support sécurisant, design, réglable dans les deux sens et adapté à quasi toutes les enceintes bibliothèque, n'hésitez pas une seconde, ce produit est le seul existant de ce type et à un prix imbattable ! Merci Amazon, délai, emballage etc au top!

I supporti sono belli esteticamente e si adattano ad ogni ambiente. Robusti e facili da montare e hanno un bel range di larghezza e regolazione in orizzontale che in verticale. Forniti di tutto il necessario per l'installazione (tasselli, gommini antiscivolo). Per un upgrade definitivo consiglio di mettere una goccia di silicone o colla a caldo per fissare la copertura di plastica sulla staffa perché ad alto volume iniziano a vibrare un po.

This is very well made. It was intuitive and easy to assemble and mount. The fact that the skeleton of this is made of wrought iron gave me confidence that this would last long and hold up my Klipsch speakers easily and for long. Highly recommend

La instalación fue bastante sencilla, los utilicé para un par de Yamahas Hs7 y no tienen ningún problema en tolerar el peso. El ajuste es bastante cómodo y no afecta a la construcción del monitor