HiLetgo BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit

Documentation is slightly lacking. Controls one motor bi-directionally. I used with an Arduino Mega (2 pwm pins, 5v times 3, and GND). I used them for a large robot (IGVC so ~100 lbs) and it worked very well on carpet and pavement but unfortunately the thick grass caused the bridge to eat about 8 out of 12 VDC so the wheels wouldn’t break away. They were undersized for this application but the linearity of operation in both directions is excellent. Had no issues with heat. All 4 came in excellent condition. Great for a medium to small torque application. I’ll find another use for them.

First off, it works perfectly for my low current needs. This can be use to individually control the speed of two separate motors, unidirectionally. Or, one motor bidirectionally. This is done thru two pwm signals and two enables. I didn’t use the overcurrent signals. And give it 40ma of 5v as well. When driving one motor, hold one pwm to zero while pwm the other. To reverse, do the opposite. Easy peazy. Now the quality. The heat sink was rattling. I decided to take off and there was a little blob of solder under one chip, so even if I tightened the screws it would not make good thermal connection. But my bigger concern was that the heat sink could potentially short out other vias, not the ones to conduct heat but rather ones for the circuits! For this design flaw I’ve removed one star. Turns out for a couple amps I don’t need the heat sink. If you need to push 20+ amps, then this would get important. Addition of a silpad or cutting clearance for other vias would be even better with some heat sink grease to boot! Can’t beat the price though, great value even with its short comings (pun intended)

HiLetgo contacted me (email) the day the part arrived, was it functional and was I satisfied? Yes to both so I can't comment on their customer service. I've only tested the driver under light loads (<2A) and it works great. Other reviews suggested inspecting the driver before applying power, which is a good idea regardless, and I found several tiny solder balls lurking behind pins of the BTS7960 ICs. The driver was shipped in a padded mailer, encountered some rough handling and several header pins got bent (straightened with pliers). Other comments: mine arrived with no documentation (easy to find, just search IBT-2) and "the supply voltage 5.5V to 27V." means motor (load) voltage range. It will not work with 5V. Yes, I would buy more.

If you read reviews; you already know units include bent header pins and overheating issues. However this review will address root cause of fundamental design and manufacturing deficiencies. Header pins are bent because all units are placed directly in ant-stat bag without protection; 80:20 chance you will receive damaged header pin. More seriously are design and manufacturing issues that render device non-functional and limit advertised performance. Design uses BTS7960 IC, which represents good performance H-bridge driver. However PCB design accommodates poor thermal heat transfer mechanism from chip tab to heatsink. PCB uses array of vias to transfer thermal flow to aluminum heatsink. This approach is completely inadequate to remove sufficient energy from chip for operation anywhere close to 43A as advertised. To make things worse, design includes no thermal pad under heatsink to electrically isolate or increase Q-flow. Both units purchased non-functional out of box, with direct short-circuit between motor output terminals. This short-circuit was due to fact heatsink aluminum was bolted down directly against bare PCB vias, without any electrical isolation pad. Apparently designer intended to use aluminum heatsink thin layer of anodized coating to provide reliable electrical isolation between motor outputs (which most likely was sufficient to pass factory testing). This problem can be corrected by adding thermal pad under heatsink. However Q-flow problem is still insufficient to remove energy for full current operation. Solution: Remove both IC's from PCB. Machine two square holes through PCB directly under IC's thermal tab. Place copper heat transfer pads on back of IC's to conduct Q-flow through PCB. Place silicone isolation pad between copper pads and aluminum heatsink. Finally place 50mm fan on threaded spacers directly under heatsink fins using existing PCB mounting holes. Now unit will function as intended.

fais le jobbe avec les perte

Fácil de configurar, lo uso para controlar piloto automático embarcación

works like BTS7960

Very handy module to have at a great price. I had some trouble trying to use mine, but I think the problem was with my attached circuitry. The first one I bought is now happily running and the spare waiting for something big to drive (I've checked it works). Having the current sense pins of the drivers available is a nice bonus although I didn't try to use it. Like some other reviews, my first module had one of the driver chips dodgily attached, with a couple of its pins very close together. Easily solved but potentially catastrophic, so check yours over before use. Both modules also arrived with the control headers a little bent as they're shipped in nothing but an anti-static bag. Again easy to fix but also easily remedied by the supplier with a cardboard box.

Questa è la seconda scheda di potenza che acquistiamo e funziona molto bene .Attualmente la usiamo a 12 VDC ma le prossime applicazione che realizzeremo saranno per motori DC a 24V , dopo potrò dire come funziona anche a quella tensione. Attualmente viene utilizzata abbinata ad una scheda di ARDUINO. Prodotto molto valido