Victron Energy SmartShunt Battery Monitor (Bluetooth) - Victron Smart Shunt - 6.5V-70V, 1000 amp

I bought the Victron Energy Smart Battery Shunt to add Bluetooth monitoring to my battery power box, and so far it has worked really well. I haven’t noticed any interference or RFI issues, though I don’t have a precise way to test for it. I’m happy to have this separate smart shunt rather than relying on built-in Bluetooth on a LiFePO4 battery. The setup was straightforward, and the detailed in-app insights are very helpful for tracking battery health and usage. Potential Uses: Monitoring home-built battery power boxes Off-grid solar systems and battery banks RV, camper, or marine battery monitoring Ham radio or portable electronics power setups Tracking deep-cycle battery health and usage Measuring current, voltage, and state-of-charge in DIY projects Managing multiple 12V–70V battery systems Disclaimer: This review reflects my personal experience only and is not professional electrical or technical advice. Always follow proper safety procedures and consult a qualified professional for installation or use of high-capacity batteries and monitoring devices.

Although this shunt will work as a standalone monitor this is NOT its intended purpose. Victron system devices are meant to work together. When I bought this I was intending to use this as standalone using Bluetooth for monitoring. Like others have said, the Bluetooth is not great. Not only is the range very short but if you stay connected too long there will be frequent Bluetooth connection "losses". This is quoted because it's not just disconnected but when you try to reconnect the shunt will act as if it's still connected which the only remedy is to pull the small power wire. After a bit of learning more about Victron products, which are the best of the best, I've learned the ve.direct port is where all the magic happens. I already have a Victron SmartSolar 150/60Tr and now this shunt. I like to watch it CONSTANTLY and couldn't keep having to pull power on both the SmartSolar and the Shunt just to get it to continue working after Bluetooth fails. Also to note, when you pull the SmartShunt power to power cycle it it will lose it current SOC reading. It will fix itself once you hit Absorb and Float but that's not always helpful if you're already sitting as a low DOD. The missing magic box for monitoring everything, not just locally but also when away, is the CerboGX. This will allow you to connect the SmartSolar and SmartShunt via ve.direct then you can connect the CerboGX to either WIFI, for away monitoring, or connect to it via Bluetooth, for local monitoring, which seems to have a much more stable connection. Fortunately for me I have a Alcatel 4G router with ethernet port, which the CerboGX also has an ethernet port. Now I have the 4G router running off the LiFePO system and connected to the CerboGX so there's never downtime. The next step was setting up an account in the VRM portal which was insanely easy and now have SO much more details and trend graphs to monitor not only real time but MUCH more such as battery curve on discharge, solar voltage, solar amp, total amps used, battery charge cycles....the list is massive and has everything you could possibly want. Yes the CerboGX is a little costly, which caused much hesitation when initially choosing it, but after getting it and fully setting it up it has been WELL worth every single penny. If you're going to make the investment into the amazing Victron ecosystem it's best to do it the right way. You will not be disappointed and will only want to see just how much more amazing it can get....and Victron devices can expand further than your wildest imagination. I can't express enough just how much I initially wanted to go cheap but let me tell you....you will need to buy more components to any system and Victron makes this near dummy proof. Just read the manuals for each device carefully and don't go over any limits they set. That's all I have for you, happy solar harvesting!! My System: -10x Renogy 100w compact with their tilt brackets (5S2P) -Victron SmartSolar 150/60Tr (yes over-paneled to get to peak charge sooner) -Victron SmartShunt 500a -Victron CerboGX -2x Chins 12v300a (2P for 12v system/ gives me options to go 2S for 24v) -12v1200w Giandel (2400w surge for a few seconds) Considering 24v3000w Giandel and all I'd need to upgrade to a 24v system then many fuses and circuit breakers throughout I know my pictures have a wiring mess but this is only due to not knowing what more I was going to add/change in the system. Once I decide if I'm staying 12v or move to 24v, and get the 24v inverter(they're MUCH bigger but all I need for this change) then I will be changing fuses/breakers and bundling all wires to fit my usually OCD/Perfectionist tendencies. And yes that is a raspberry pi screen I'm using for direct monitor from the CerboGX haha I also included the VRM (Victron Remote Management) views from PC, 2 darker views, and the one from the mobile device app. Thought that might be helpful in understanding the value of the CerboGX and VRM (which a VRM account is free)

I installed the Victron Energy Smart Battery Shunt to keep an eye on my boat’s starter battery, and honestly, I wish I had done it sooner. The Bluetooth monitoring works perfectly—I can now check my battery’s status from anywhere on the boat without doing the awkward “lean over the engine bay and pray” maneuver. The readings are accurate, the setup was simple, and it’s already prevented at least one “guess we’re not going anywhere today” moment. For fellow boaters who like reliable tech (and dislike being stranded at the dock looking confused), this thing is worth every penny. If my starter battery had feelings, I’m pretty sure it would thank me. Highly recommend—5 stars! 🌟🌟🌟🌟🌟

It's a battery shunt, doesn't need much more info than that. The Bluetooth connection is kind of short, around 100' but it works well and functions great with the app when you stand close enough.

As usual, Victron continues to provide exceptional quality, fit, finish and utility. Installation is a simple, straightforward process that requires only one additional short cable of the proper gauge for your setup. The included positive wire and secondary positive (for monitoring a second battery bank or midway point) have built-in fuses. One note - the bolts on this require 5/16" or 3/8" wire lugs on the wires from the negative battery terminal and to connect the load or bus block. The shunt itself is very sturdy, and designed for easy mounting in a small space near your battery. It also networks wirelessly with other Victron Smart controllers and other products over Bluetooth to allow them to share information, via the VictronConnect app. A few minutes of reading is all that's necessary to input the battery information and other parameters via the app, and before you know it you're up and running with detailed information that assists greatly with fine tuning your system. You may, like me, find yourself wondering how you ever got by without this addition to your solar power system. I put it off, questioning whether I really needed this. From now on, I'll have one of these on every system I install!

Victron ! No more to say . Excellent quality, easy to install and works seamlessly.

I've been upgrading the boat's front end electrical system including a 120 amp alternator, so I needed to upgrade from my 100 AMP Shunts. This thing is fabulous. (It's in the project box on the top right of the image). no more wiring loom going to a display. Along with the Victron shore power charger I can now see much of my electrical system performance right on my phone from the cockpit thanks to the bluetooth connection. Dead easy to install, I have it hooked up to my house bank, but it also can monitor my start battery. Makes diagnosis of problems much easier having all the data in my pocket anywhere on the boat. BT range is not huge but adequate. Can be blocked by the engine depending on where I stand. but the BT booster is an available option. Money well spent

Perfetto, molto semplice da installare se si ha manualità ovviamente. Gestione da app eccellente, mi raccomando seguire le istruzioni del manuale on line per i settaggi della batteria, se è al litio ci sono dei parametri da modificare, na li trovate nel manuale. Victron è sempre una sicurezza.

Le module enregistre 45 jours de données aux on ne peut accéder qu'en bluetooth depuis l'application. L'exportation est totalement verrouillée par Victron, il faut ajouter un Cerbo gx qui coûte 300€ et ne permet d'avoir les informations qu'à partir de son installation. Je n'en reviens pas

Pues está bien caro pero es funcional, te permite saber el estado de la batería así como la tendencia histórica de 6 meses hacia atras El único tema es que el tornillo está muy gordo y no entra el adaptador de mi bateria, ojo… esto no corta carga ni actúa como gestión de la batería, solo es para observación