Elite Screens 120" Fixed Frame Projector Screen 16:9, 4K/8K UHD CineWhite UHD-B, ISF Certified, UST/Short/Standard Compatible, SB120WH2

The product comes well packaged. Instructions could be better but they work. If you take your time, the installation is relatively easy. I laid down moving blankets during assembly to protect the product. They also provide a protective cloth to lay the screen on. The trick for the frame is to keep screws loose until they are all inserted. At that point, you can shift the corners to make them 90 degree flush and tighten all bolts. The screen wasn't hard either. They give you a spring tool to pull and snap over the tension rods that are inserted into the screen sleeve along the edges. If you have worked on a car engine, you know to torque in opposite corners to even the tension. I started with the two springs closest to the corner edge and then went to the opposite corner and then did the same with the remaining corners. Then I repeated that pattern and installed the second spring closest to the corners. You must hold the tension rod as tightly as possible to the edge of the screen to allow the spring to hook over the tension rod. While the tool provided worked, it would be easy to miss the tension rod and tear into the screen. I used needle nose plyers to change the angle of the spring hook to come at the opening from the top and then curl over the tension rod. I also found that I had better control of the spring and it went quicker. After that, follow the instructions and start in the middle of each side and then half split. After that, it was easy to install the remaining springs. The screen was perfectly tensioned when completed. When preparing to mount to the wall, I laid the brackets on the back of the screen and measured the distance between the two screw slots with brackets level and fully inserted into the mounting slot. The instructions said 68.1" but I measured 68.25 and went with that. I screwed the brackets directly into studs, ensuring that the brackets were perfectly level for both the upper and lower brackets. I set the screen on the top brackets ensuring the screen was sitting on the bracket properly. At this point, you can adjust the screen horizontally. Once it was in place, I pulled the screen down until it snapped into place over the bottom brackets. It was quite snug and having the upper brackets drilled into the studs ensured the top mounting screws didn't come out of the wall. The screen fully mounted has no play or chance to fall off the wall. Overall, this is a solid product with a taunt screen and nice clean black border that met all of my expectations.

The frame of the screen is covered by a layer of velvet. It reminds me of some movie theaters. I did some adjustments in my projector and to the AppleTV and the picture quality is outstanding. Also, pay attention to the way you have to assemble it, the springs are easy to put through the holes, and the company provides the necessary tools plus two pair of gloves. Highly recommended, easy to assemble and great and sturdy materials. This screen will not bent by accident due to design flaws.

Overall product quality was great and assembly install was didn't take longer than 30 minutes. Frame and screen can be assembled by yourself though due to size of my screen (110") it was definitely nice to have a second person to help balance it while mounting it to the wall. Product did not include assembly/installation instructions but this online video by the manufacturer was very helpful though slightly outdated from the product I received. Assembly: This step is fairly simple and took about 20/25 minutes. Mostly consisted of using the included brackets you screw the horizontal and vertical frame pieces together. The screen is then rolled out and attached to the frame using numerous small springs. Product also included all necessary tools to make assembly easy. It felt like I was putting together a trampoline. Because of the spring design the final product ended up wrinkle free and required no additional work to fine-tune the screen tension. I will note that there were some very small wrinkles that did disappear by the second day. Attaching the screen to the wall: Mounting the screen to the wall is also very easy with the included brackets that the frame rests on. Having a second person was very helpful to make sure the brackets were level and to avoid having the screen tip over while lifting into place. The screen is very light and I could have lifted it up by myself but due to the size it was a little difficult to balance especially while trying to avoid touching the screen (Note: kit comes with gloves to wear while doing this to avoid oil transfer from your hands to the screen surface) Final verdict: For the price the screen quality exceeded my expectations. It looks great on the wall (picture included in review) and even with an entry level projector (Epson 3200- Cost $1200) the picture looks great and gets compliments all the time. I would highly recommend this product for your home theater needs.

Great screen and a relatively good price. Does seem to make the colors especially pop a little more, and it looks good. But be warned, especially for the larger sizes, that assembly isn't easy. Not complicated per se, but just work. 135 little plastic buttons to snap together (which occ pop apart and have to be fixed), 135 springs to attach to stretch the screen onto the frame. We used 3 people to hang this thing once done, just to make it level. And yeah it's hard to hit studs for the every one of the mounting bracket holes, but 50% ain't bad (this thing isn't too heavy). If not for the awkward assembly would be 5 stars. Will see how it holds up (ie if plastic starts popping off and the springs start tearing the screen, will update).

This definitely gives a brighter, richer more colour vibrant image than simply projecting onto a magnolia painted wall. The screen surface is also very flat and so avoids problems caused by creases in much cheaper screens. The only small issue I notice (and it is small) is that the screen is not quite big enough for the frame in the vertical direction, meaning that small sections of the black screen edge are visible. I hope these will gradually disappear as the springs stretch the screen. Getting the springs on during assembly is difficult and I found I needed a second person to help.

Perfeito e fácil de montar

Grandísima pantalla de proyector. Venia de una de techo y nada que ver. El estar tensionada y la calidad de los materiales mejora mucho la experiencia. Eso si, al menos dos personas para montarla.

I purchased the Elite 150inch Screen. It is an excellent product. Communication with the seller was excellent and the product arrived on time.

Cost effective upgrade for our theatre room which has become a permanent room in our home. Vast improvement over our previous screen, very nicely made. Picture quality is also improved with our current projector. Much better contrast and brightness than our previous screen. Parts were well packaged and labeled. The only comment I would share is the tape on the protective wrap on the black frame did mare the black a little. But it’s minor and I still feel the product is worth 5 stars. The screen does take time to assemble, be patient I found the instructions straight forward and easy to follow. Screen was also simple to hang. For the money, great product and it arrived quicker than expected.