Mounting Dream Black Alloy Steel Speaker Stands, Height Adjustable Bookshelf Speaker Stand Pair, Universal Fit, 11 lbs Capacity, Set of 2 for Bose Polk JBL Sony Yamaha - 42" Max Height

I got two sets of stands (4 units), added a few silicone pads and Velcro cables ties via Amazon, and now have perfect mounts for the four Quad speakers. The stands are high quality, easy to assemble and versatile. Mounting Dream MD5042-2 speaker stands can be a good solution for mounting Sony Bravia Theatre Quad speakers. Cost is now about $80 for two stands; I got two sets via Amazon and added a couple items to get the kind of mounting I wanted. The stands allow for multiple mounting approaches, but the Quads are of unusual design, so I added two items below for mounting the Quads (I mounted the Quads with their Sony table-stands attached): 1. Rubber mounting pads: Hudson Hi-Fi 1" Platinum Silicone Isolation Dot, Non-Skid Isolation Feet - With adhesive back - 20 Duro - 16 Pack (via Amazon, $18). Stick four dots on top plate of each stand to support the Quad-stands (align dots with edge of mounting plate). 2. Cable ties: VELCRO Brand ECO Collection | 5 Inch Small Straps for Cords | Reusable Cable Ties | 3/8" Wide, Black, 50 Pac (also from Amazon, about $12). Thread 4 cables ties through the four, 4mm slots in the speaker mounting plate and tighten to secure the speakers on top of the isolation dots. Make sure you’ve installed power cord before mounting speaker. The Mounting Dream speaker height is adjustable and the plastic base-feet are adjustable to correct for uneven floors. The base is “domed” so excess speaker power cord can be coiled and hidden under the base plate. The speaker power cord is hidden inside the support tube. One needs to pull the speaker-end of power cord up through vertical support tube (internal structure of tube prevents gravity feed of speaker-end of power cord). I used an electrician’s fish-tape wire-puller. Something like an undone wire coat hanger would also work. I used twist-ties (from plastic food bags) to temporarily attach the power cord to the fish tape for the pull-thru. Note that the Mounting Dream speaker mounting plate is barely large enough to accommodate the Sony-stand, so use care in aligning silicone dots and speaker base. The isolation dots should align with edge of the mounting plate. You won’t need the MD5042 “Speaker Attachment Unit” using the mounting approach described here (you’d only need this if using back-of-speaker mounting hole … a whole different, off-centerline mounting method).

Assembly requires lining up threaded holes in the interior pipe with unthreaded holes in larger outer pipe and using the hex wrench to screw the pipes together. Typical but a bit fiddly for me 'ol hands. Also black-on-black hard to see. Better would be a slot in the outer pipe and ready-set bolts sticking out from the inner which slide into the slot and are tightened with a strong wingnut. No fiddly tool needed. Same for the upper connection which is slightly but not fatally out of align likely due to the crimping of the inner pipe which inevitable shortens it by a 1/16th inch or so. As the threaded holes were likely set in prior to crimping, this moves them down a tad versus the outer pipe holes which were punched with a certain alignment that is not there after crimping. Net: slight misalignment not fatal but do not expect the holes to be properly centered. Just push real hard on the top pipe to encourage alignment as best you can. Back speaker support bracket adjusts horizontally and vertically. High enough for my Polks and design permits wires from wire posts to pass through unobstructed. This is a very clever, unique, successful design. So we now have 2 very strong and satisfactory speaker posts. Well worth the money. Might spray white Rustoleum on them to blend with the wall and replace speaker fabric with white available right here on AMZN. Then we would have something truly superb. Net: these posts are very good. Buy them, say we.

These fit the Q990D speakers perfectly. Setup was easy and the hidden cable management tubing makes the whole setup a lot more discreet in the living room. Build quality is a hefty, sturdy metal, have had a few weeks now running vacuums over and so forth and no scratches display. This stand allowed me to shift speakers behind sofa and to a proper height, which unlocked the surround sound bubble of the Q990D.

La guía de instalación es rápida y simple. Muy fácil. Material de buena calidad. Peso firme y apropiado. De estilo simple sin mayor diseño estético. En el soporte posterior hizo falta una pequeña pieza transversal horizontal que permita sujetar bocinas con sujetadores u orificios separados horizontalmente. (Como se ilustra en la foto de unos satelites Yamaha). Por lo demás, son adecuados, robustos y discretos.

ソニーSA-RS3S用に購入 下部に重みがあるため見た目以上に安定感があり満足 ただしいくつか注意点も ・スピーカー取り付け部の底面が凹んでいる そのためスピーカーが小さめだと底足が宙に浮いてしまう 自分の場合は金属のプレートを両面テープで取り付け土台を使った上にスピーカーを置き、背面ネジで固定しています(M5ねじは付属していないため別途必要) ・筒内部の拭き取りが必要 コードを通せる筒部分、中身は結構汚れているので事前に清掃しておくのが吉 その他は特に不満点もなく満足です

Good product

Excellent quality product. Easy to assemble and fix. Several options for different size and types of speakers

This is the kind of purchase that makes one happy. The box is neatly and tightly packed. Each item is labeled well, and the instruction manual is clear as day. The product contains everything you'll need to set up most of your speakers (except wood screws). Unfortunately, my satellite speakers are a millimeter too tall to aptly secure from the back, but that was easily remedied by a thick double tape (instead of using wood screws from the bottom). Edit: there's a slight wobble on my tiled floor which I can't see to get rid of no matter how much I try to adjust the feet. Since the base isn't heavy, there is a mild risk of tipping over. Something to consider if you have kids.