SmartThings Multipurpose Sensor, Know if Windows and Doors are Open, Single

I have bought several SmartThings Motion Sensors (2018 version) and they work reliably and perform well. I have these installed within a few rooms around my house and primarily use them to control lights when someone enters/leaves the room. When positioned well they can detect motion instantly from the other side of the room without any problems. I would say that it probably takes about a second for my lights to come on when I walk in the room. Battery life seems to be good also. I have a few other branded Zigbee motion sensors and the Samsung 2018 sensors seem more responsive than all the others I have. I also do like the magnetic base design which can be placed anywhere and the sensor can be easily moved in any direction. As with all the Smarthings sensors, they are also easy to connect to the hub. They also do measure temperature but I don't have any automations setup based on temperature so I have not really used this feature. Tip: I wanted my lights to switch off as quickly as possible after I have left a room, however I have these motion sensors in rooms such as my office or living room where I may sit down and not move much therefore the sensors would turn lights off after a short time because no movement was being detected; this was somewhat annoying when actually still in the room. To get around this, I have configured my automations to not turn the light off only when the sensor detects no motion in the room I am occupying, but also when motion IS detected from another sensor in an adjacent room! When I leave a room, I have to go past other sensors everytime so I now have automations configured so that when motion is no longer detected in the room I have been in, it also checks if motion being detected in the adjacent hall ways, only then will it turn the office/living room lights off. This seems to work well even if you leave the room and are then only in the adjacent hall way for a brief moment. You're welcome! Overally, great sensors, highly recommended.

Work straight out of the box. Open and close feature worked great and response time is excellent within SmartThings. It is a bit slow when linked to IFTTT on a virtual button to control a sonoff relay. There is about 2 seconds delay. The vibration sensor is great, you can set it up to send you an alert or trigger an automation if a vibration is detected. One great feature I like is that you can see all events over a period of time and the temperature sensor is very accurate. It could do with being smaller and have more flat surfaces so you can mount it 90 degrees on a sliding door. Overall great sensor, I just hope one day Smartthing can work with HomeKit... wishful thinking I know.

These things cost a bit more than some brands, but they are solid! Work very reliably and easily. I use them with home assistant and deconz. I have 5 now but I’ll likely pickup more in the future.

I got this to use for two reasons; 1) Work with my smart bulbs to turn on after a certain time 2) Work with our smart alarm as a motion sensor Easy to install? Super easy. Literally take off the sticky section and that bottom section sticks to the wall (plan out where it is going first as it will be hard to remove) then get the physical motion sensor and it is magnetized. Easy to sync? Again yes. I just downloaded the Smart Things app and it does all the legwork. Looks good? Its very discrete and I have mine in a high traffic area of my home and you never notice it. Battery life? This one I cannot fully answer yet and only time will tell but had it a few months and still works fine. I am not sure how to replace the battery but will update when I need to. Cannot recommend this enough.

As a user of both the SmartThings and Philips Hue ecosystems I have motion sensors from both systems. When deciding which new one to buy I’m very glad I bought this new 2018 version. It’s cheaper than the Hue equivalent and it has a posable magnetic base (with 3M sticker). Its back is also magnetic which gives you so many more options for positioning it how you like. You can trigger your own SmartThings scenes or use Hue scenes via Alexa and it works with the older V2 hub. I’ve been using it for about a week - it’s responsive and accurate and I’m very happy with it (just ordered another one).

Attached by 3M sticky pads which do not work. No other way of attached. Activated the system which failed after 20 minutes and unable to reset it.

Das Ding ist schnell gekommen und war auch schnell angebracht (vorsichtr, die Klebeflächen halten sofort bombenfest, also vor erst gut überlegen, wo und wie er hinsoll!). Die Einbindung ins Netz erfolgt über SmartThings, entweder, das Handy findet den Sensor gleich über den Scan vom handy aus oder man nimmt den QR-Code auf der Rückseite. Der Rest ist ein bisschen Denksport, wie man die Routinen einstellt. Es ist aber recht einfach und intuitiv. Die Benachrichtigungn klappen vorzüglich. Also ich kann den Sensor nur empfehlen. Anklopfen habe ich jetzt noch nicht probiert, weil ich den Sensor über die Anwesenheitserkennung deaktiviert habe, wenn ich daheim bin.

It works perfectly, detecting vibrations, temperature, and whether the door/window is open or closed. Requires the Hub to function.

Gros problème sur Home assistant le capteur détecte bien quand il est ouvert ou fermé par contre au niveau des vibrations et des mouvements c'est une vraie catastrophe. Soit le capteur détecte uniquement lors d'une ouverture ou d'une fermeture mais au niveau des vibrations de l'inclinaison ou autre chose c'est une vraie catastrophe sur Home assistant. J'ai essayé de l'appairer plusieurs fois de le changer de place d'orientation mais c'est toujours la même chose.

Che ne vale la pena per domotizzare casa comprare dispositivi originali all'app ed il gateway samsung funziona benissimo oltre al sensore di apertura finestra o balcone tiene anche la funzione del controllo della temperatura per ogni ambiente che è istallato, quindi vi consiglio di acquistare questi sensori senza pensarci Aeotec di Samsung il topo.dei device.

Fait bien le travail. 1 petite chose me gêne: le capteur d'axe n'est pas utilisable dans SmartThings. (photo 2) On voit sa position "X Y Z" (photo1) mais c'est juste à titre informatif !! Inclus dans une future mise à jour ?