ARCTIC TP-3: Premium Performance Thermal Pad, 100 x 100 x 1.5 mm, (stackable to 2.0 mm without performance loss), 1 Piece - High Performance, particularly soft, ideal gap filler, bridging gaps

Used one pack of the 0.5mm, 1.5mm and 2mm pads while overhauling my RTX2080. They were all uniformly excellent quality, with the right amount of stickiness and firmness. After the overhauling (including replacing the paste with Arctic MX4) my card went from up to 98 degrees Celsius at max to 87 max (with a higher hotspot). It also took almost all of each of the three packets to replace all the pads; this almost certainly won't be needed unless you are effectively practising like I was but it gives an idea as to the amounts needed. (I did look up the thicknesses on a blueprint for my particular card and had to layer the thicknesses.....which as Arctic say is both east and effective ). Easy to install with patience and a sharp craft knife to cut them and I'm happy with the performance improvement.

Last Time I used thermal paste was back 15 years ago trying to get rid of the red ring of death on Xbox. It was messy and really hard to apply (me being a amateur thermal paste user) to cover the processor in depth and all corners covered. This pad is a game changer its literally this simple. Clean processor with alcohol carefully clean heatsink measure processor cut to fit, take of shiny protective sheet apply to processor and then proceed to take of diamond sheet this one was 1mm thick if you need bigger use two pieces. A complete novice here and this has stopped my pc from throttling this stuff works I have no problems with heat dissipation now. Also there is enough here to reapply many times the size for the price is unbelievable simply because it takes the mess away and makes it easy for novice's like me. Delivered very quick.

Great for Xbox Series X full pad replacement. Thermal conductivity is far superior to the stock thermal putty. Pads can easily be cut to size using a craft knife and are reusable if you are careful with removal. 1.5mm is the correct thickness for Xbox series and Xbox one consoles. Great cost Vs performance. Cannot be used on the APU die itself, only for RAM, VRMs, SSD and expansion card areas. Also available on Amazon is Artic MX-6 which is great for the APU and bottles of isopropyl alcohol 99.9% for thoroughly removing the old paste/putty from all locations.

Used for a PS4 pro refurb. Significantly improved temperatures. Used about half of it, so the pad itself should be big enough to refurb 2 consoles or maybe 3 GPUs. Wouldn't recommend for a modern flagship GPU but an older RTX 20 series or earlier would do fine with this. It's quite awkward to cut cleanly, you really need a sharp blade, not scissors for a good cut. It picks up fingerprints very easily and will deform or even tear under tension but besides that it works exactly as you'd expect - just cut to size and place where it's needed. Be sure to check the thickness, buy the thinnest pad that'll work for your situation, don't try to squash a thicker pad to fit a thinner gap.

Purchased to use in PS4 Pro along with replacing the thermal compound. Has made it go from sounding like a jet engine to significantly reducing the noise. Product is slightly awkward to cut, I used scissors, but suspect a decent craft knife would be better. Have plenty left over if and when the time comes to open the PS4 again.

Great product, of course is very brittle as expected so use it very carefully and be prepared using proper tools for it. My PS4 Pro was very loud but after replacing the thermal paste and the pads my console is suddenly very quiet, just whispering. So performance is brilliant. Not too sticky so just beware.

good but too expensive

Without a doubt, worth it. Don't even hesitate to buy this, Crazy good price and crazy good performance. used this alongside MX7 to Re-paste and Re-pad my 3080 Suprim X that was running hot after years of no maintenance. works like a charm, brought hot spots from 105 °C down to low-mid 70°s, Mem temps around the same mid 70°s and Core temps with MX7 never leave 60°s. 1000% worth it. (STACKING WORKS AS INTENDED. NO PERFORMANCE IS LOST FROM DOING SO.)

Kaliteli ürün.

Arctic har aldrig svikit mig förr och denna är inget undantag, grafikkortet (RTX2080) behövde nya och har fått nytt liv igen!

最近のMBに付いているM.2用ヒートシンクパッドと同じくらいの厚みです。

Bought to repaste a MSI 3080 x trio lhr 12g. 1mm is for the vram chips around the GPU die. Absolutely phenomenal. Not only are they cheaper but the definitely make better contact vs the gelid kit which is actually almost double if not double the price. They also ran slightly cooler. Memory pre re-pad and paste was at 94-97c/ fans 65%. Gelid kit memory max that i saw was 85 at 65% and the arctics was staying at 83 but max of 84 at 65%. Reason for removing the gelids is because i didn't feel like they were making sufficient contact just by eyeing it but i could be wrong. But for half the price and in my opinion better contact and 2c less i would definitely go with arctic!

Probly the best low cost thermal pads. Found it easier to use sharp scissors over a straight blade and ruler. I was impressed with the temperatures. Iv tired just about all the thermal pads amazon sells to try and tame my alienware gaming laptop temps havent even passed 90°c when running benchmarks