2.8 inch Motion Sensor Lights

I installed these up a dark stairway. The motion sensors are sensitive and the light turns on for 20-seconds. The light is a bright white so it makes it very easy to see the stairs. I highly recommend these if you are looking for a good motion sensors light. They are just the right size and work well.

Just what I was looking for. I placed one in the hallway and one in my gbabies room. They work great and the light is bright enough for me. The adhesive has worked well and the light has not fallen off the wall. They are very easy to use just attached the three triple a batteries and stick them to the surface.

Works good but one of them keeps falling down. Light is great & just right brightness.

What a great find! I needed a light inside my large mailbox because I can't see anything when I check it at night. This little light is perfect. It's off until there is motion detected then it clicks on. You need 3 AAA batteries in each, but they work perfectly. I'm buying more

Works great. Put one in my mailbox and it’s as advertised. Even in the dark of the mailbox it does well at sensing when I reach in then turns on. Doesn’t waste battery.

I loved these puck lights out of the box. They were packaged well, a very good size and easy to open to install batteries. They are solid quality and very bright. They come on briefly when the battery is installed and then go out in a few seconds and are ready to mount. The adhesive on the back of these is fierce, to the point that after being on the inside wall of a cabinet, I had to pry the light off with a knife to move it. This left most of the adhesive stuck to the cabinet ( now the light has no adhesive) to scrape off and it leaves a sticky residue. If I had expensive cabinets I wouldn't use them - DO NOT USE ON DRYWALL if you don't want to spackle and paint because they will remove both paint and drywall in removal. Make sure you know where you want these before attaching them! Now, the reason I was moving them. They really aren't sensitive at all unless in total dark. They would work very well outside at night or moving through the house in the dark, but my use was for deep unlit cabinets that I've had to shine a flashlight in to access items. I will seldom be in the kitchen completely dark so that they'll activate. This has apparently been a problem because I received an email (thanks, it helps!) with instructions that included use in other than pitch dark. Apparently I have to open them and partially cover a sensor. I'll be doing that and review if it was easy to do and worked well. If not, I'd advise a different light.

The Star-Spangled Motion Sensor Lights are wonderful. It worked out perfectly as we set it around my dad, who has dementia, bed, so, he can see at night when walking to the bathroom. I highly recommend these lights. The lights are bright and clear. We're happy we got them. They were easy to attached to the bed frame.

These are great! I put them in a couple of closets and they are nice and bright. They turn on as soon as I open the doors.

Works well, and is perfect for homes with senior citizens. I wish the sensitivity to light was a little lower. It gets activated in fairly good light, which is basically a drain on the batteries. And yes, I don't need the cashback for the rating :)

Batterien halten sehr viel länger als die Modelle, die ich auch als Treppenstufenbeleuchtung verbaut habe.

These little lights are fantastic in the hall at night. They work perfectly and they are cool light which is great. Easy to install, just stick on the wall with the included adhesive dot. You need to insert AAA batteries yourself. Totally recommend!!

Perfect

I've turned this into a bit of DIY project. Before spending couple hundred bucks on replacing the latch in my car's trunk which fails to turn on the light (despite the light bulb being okay) I decided to try this. The idea was that it would only turn on when it's darker, when I open or manipulate things in the trunk. It turned out the light detector would only turn on the light when it was very dark, so I did a little modification. After opening the back of the product and removing a few screws you'd see a printer circuit board with one chip, 6 LEDs, motion detector in the middle and a light sensor on the side. I gently painted the sensor with a permanent marker to darken it (not to make it entirely black). That made the light turn on earlier, when it was in a dark shade, not just a complete dark. I also cut one of the circuits on the board to disable 3 out of 6 LEDs since I found them to be much to bright for my needs, considering that perhaps this will extend the battery life. I mounted it in the my car's trunk and so far it has worked as expected for about a month now. We'll see how long the battery lasts, especial in cold weather but overall I am very happy with how it works. Good product!