DIY S500 Quadcopter with APM2.8 Flight Controller 7M and HP2212 920KV Brushless Motor + Simonk 30A ESC

I wouldn’t call this a kit. It’s really the S500 airframe with the rest of the parts needed to build a working quadcopter thrown in the S500 box. I added up the cost of buying the parts separately and they came to over $200 so this is a good buy. The quadcopter also doesn’t come with a transmitter, receiver or battery. I’ve been using a 2200mah 50C battery and get about 10 minutes of flying time. I found that the landing gear plastic tee is the weak structural link. A hard landing or crash will crack the tee. There’s a sheet of instructions for the airframe but nothing for the rest of the copter. I would recommend watching an online video showing the entire quadcopter build. Pay particular attention to the compass connector of the combined GPS/compass module connectors. The compass connector plugs into the I2C bus. Also, when you attach cables to the Arducopter module the grounds (black wires) are all to the outside of the module. Be aware that some minimal soldering is required. Also, the motors with the black nuts turn CW and the motors with the silver nuts turn CCW. Make sure you follow the motor placement in Mission Planner documentation. You’ll also need to download the firmware for the Arducopter module from Mission Planner. Use the wizard to set up and calibrate the Arducopter software. Then follow the instructions in the Mission Planner for the correct direction of motor spin determined with the propellers off. If a motor is turning in the wrong direction switch any two of the three wires from ESC. When you install the propellers think of them as a wing and you’ll quickly determine which way they should spin. They install so that their spin direction is opposite the nut tightening direction. Make sure you use a wrench to tighten the nuts. Hand tight is not good enough. If you’re a quadcopter noobie like me you’ll likely break a propeller or two so you should get some spares. These propellers are DJI compatible 10X4.5 with two flat sides in the mounting hole. Standard propellers won't work.

Is a good starting kit. But the FC is not supported by Arducopter any more, so I wasn't able to flash the lastest firmware. Doens't have a good instructions manual, so I needed to check many videos and articles on internet to assemble it. But I can not complain about that because is part of the fun of DIY. Came with a bad ESC so I guess I need to wait a little to finish it and test it (fly). Also one of the motors have a different sound, but can not test it until I get the ESC and have all ready to fly.

First, mine flew successfully, and so far as I can tell, everything works. This is not for the novice, you need to do research and have some experience with quads. Overall though, I'm pretty happy so far. There were a few challenges. First, the only assembly instructions are for the frame itself. Not a show-stopper, but I did have some questions on where to mount things. The flight controller mount screw holes do not line up with the third screw on each of the arms, but I just used the double sided foam tape and it seems to work. Depending on your props, you may need a prop reamer. No instructions for which motor goes where, but I put the silver ones (clockwise tight screws) on the front right and left rear (as viewed from above). That turns out to be the right way. On startup, forward right and left rear motors should spin counter clockwise. I'm a helo guy, so I put blue threadlock on all metal to metal screws. The only thing that really frustrated me was the GPS antenna mount. The carbon fiber arm doesn't secure well, I had to use epoxy to get it to stay in the base mount and the top. Not a huge deal, just make sure you've got some. Props are Gemfan 10x4.5. Added photos. Recommendation: DO NOT mount XT60 like I did on the top - I had to run wires from the bottom to another XT60 after I realize this was awkward. If I had to do it again, I'd mount it in the same spot, just on the bottom of the plate instead of top as shown. I tried mounting my receiver between the two main frame plates, but moved it to the front so I could use the satellite connector and maximize the antenna exposure. The way I secure the antennas and keep them at 90 degree angle is bush league, but it works. Those are coffee stirrers tied to the rails with dental floss.

With the aid of on-line videos I was able to assemble and test the quadcopter kit. I provided my own transmitter, receiver, and battery. One of the electric motors was defective. In addition, after assembly and testing, the quadcopter would not acquire the GPS satellites. As a result, the motors will not respond to the throttle control. The website provided in the kit was no longer active and no other assistance was offered. Short of returning the entire kit, I have no way to get a replacement motor or repair what appears to be a defect in the GPS receiver system.

I really really wanted this to work. It came with no instructions, the flight controller is out of date and discontinued, and using google there are some many variations that it's unhelpful. I get the thing built just to have it flip over before it can even get an inch off the ground. As much as I hate to say it, save your money and invest in a DJI drone. As much as I did enjoy the process of building it, it is not worth the price to watch your hard work just crash before it can even take flight.