Raspberry Pi 4 Case with Cooling Fan and Heatsink for Pi 4B

I originally bought a Raspberry Pi 4 to use with a Picar-x setup. I built a smart home system using sensors so that when my dog approaches the window to go potty outside, it plays a voice alert saying "Please open the door." Because the sensor was so sensitive, I recently had to get a new Pi 4, and I bought this case along with it.This case fits the Pi 4 perfectly, and having the cooling fan included is a huge plus. It’s a great compact size and feels incredibly sturdy and durable. Highly recommended for any DIY project!

Well made and easy to assemble. Nice quality, and tolerances are good for plugging in cables properly.

My 14-day assessment is this is a great value case. A few quick points:Fan volume:The fan was noticeable on the 5v connector but not obnoxious. I’m noise-averse to fans from equipment on my desk so I dropped the fan to the 3.3v connector on the Pi and couldn’t hear a thing, even 12 inches.Temperature (at 3.4v “low” speed)I ran a stress test ($stress-ng) and never went above 75C using the included case, fan, and thermal tape. My ambient room temperature was 72F (22C), and at no load the P4 averages 43-44C.//cut//<beginning 20 min into stress test>16:40:01 UTC - Temperature: 75.0 C load average: 4.08, 4.02, 3.7116:45:01 UTC - Temperature: 73.0 C load average: 4.08, 4.02, 3.8116:50:01 UTC - Temperature: 75.0 C load average: 4.08, 4.02, 3.8816:55:01 UTC - Temperature: 73.0 C load average: 4.08, 4.04, 3.93<test stopped at roughly 16:57 UTC>17:00:01 UTC - Temperature: 47.2 C load average: 0.11, 1.96, 3.1317:05:01 UTC - Temperature: 44.3 C load average: 0.00, 0.71, 2.2517:10:01 UTC - Temperature: 44.8 C load average: 0.00, 0.25, 1.6217:30:01 UTC - Temperature: 43.3 C load average: 0.00, 0.00, 0.41//cut//Without modification, the Pi 4 CPU throttles at 80C to preserve itself, so this was really a test to see if I would ever need to adjust to a higher speed depending on my use case.If you want to duplicate the test, just make this into a script and add it to your crontab at 5 min intervals (*/5 * * * * /path/to/script)echo "`date` `landscape-sysinfo --sysinfo-plugins=Temperature` `uptime | cut -b 39-70`" >> mytempOne complaint: The screws.The screws on this case are very poor quality. They’re tough to get in and easy to strip. Not a problem if you intend to set it up and the ignore it forever, but if you want to take the case apart frequently for different projects then I recommend a different model. I think 1-star off is justified for a case you can only disassemble a few times, especial for a project board.Overall, great value case and at low speeds the fan is inaudible and still keeps the Pi4 below throttle temp.

I used this case for a project that needed the device to be on 24/7, and the fan was a HUGE help. I will admit that the fan does make an audible noise that can be heard from a few feet away, and unless you screw the case tightly or have it pinned/taped down, it can vibrate through the plastic making the noise very loud. Outside of that, it gets the job done perfectly. Only thing that would be great is if there was an optional clip-in piece that would cover where the GPIO pins are, since there are some projects (like mine) where I didn't need them and they were left out and exposed which wasn't suitable and I had to carefully cover over the gap with a piece of clear packaging tape which did the trick. Otherwise, great case and got the job done!

The case is very effective and ascetically pleasing. It is a simple install procedure, that is shown directly on the amazon page (no instructions included.)The fan itself isn't terribly loud, but isn't silent. At 6 inches away it is running about 32db while room ambiance is 28db. Putting the mic right next to the fan resulted in around 50db. That being said, it's terribly effective.When running a simple stress test, the CPU will spike to 59°C after two minutes with the fan running. Without the fan, the CPU spikes to 72°C, a 13°C difference! I honestly did not expect it to make that much of a difference. I still don't think I will keep it running for the majority of the time, but if I am ever running stressful loads on the Pi, I will make sure to have it plugged in.The case looks very professionally produced, except for the large slot for accessing the pins. I wish it came with a cover that you could snap on to protect them when not in use. However, for the price I'd say this thing is unbeatable!

The Pi4 fit perfectly in the case and there were no issues with that. What I did have an issue with is the long legs on the fan wiring. You can see on the back side of the pictures, they stick up way too high. I'm going to fix this problem myself and it's not THAT big of a deal. The fan's speed can be altered by connecting to either the 3v or the 5v pins. I am going to see if the 3v speed is sufficient because the fan at high speed is just a tad noisy and I have enough noise in this room without adding more.You can tell by the pictures, that I wanted more than a bland black case. I grabbed 3 cans of spray paint and had an instant piece of art.

The case fit well and I like it. The heatsinks are ok too. The fan however has already failed just a few months after it was put in service.

Things to note about this case. 8 $ for a decent case! Comes with fans and heatsinks. Instructions for the case have you applying positive pressure (air flowing in) to the board. With the design of the case (despite having a vented front) heat kinda just swims around inside the case. Thankfully, they thought of this and provided a fan that could be put either way. So, reverse how the fan is and now we have negative pressure (pulling heat out of the case, in other words air being pulled out of the case). Otherwise, cutouts and microsd card access are great. The holes next to the fan allow for ribbon cables to be run. So that means if you have such things lying around you can use them. My only small nitpick would be that there should be a latched “door” for the gpio headers as an extra layer of protection. Now just waiting for micro hdmi to hdmi cables and then I can get started on a small project

Took me a little longer to put together than I wish to admit. They really just throw parts at you with no instructions. I am still new to using Pi.

El ventilador y los disipadores excelente

جيد ، والتغليف متوسط

Came in fast a good condition

Product looks ok works for me but the fan was missing